Unicorn Tapeworm - Revision history

F3l1x at 20:39, 10 December 2024

2024-12-10T20:39:03Z

F3l1x at 20:38, 10 December 2024

2024-12-10T20:38:36Z

F3l1x at 16:10, 28 November 2024

2024-11-28T16:10:40Z

F3l1x at 20:28, 2 July 2024

2024-07-02T20:28:07Z

F3l1x: /* The Unicorn Tapeworm */

2024-06-10T20:48:12Z

‎The Unicorn Tapeworm

F3l1x: Creation of the wikipage

2024-06-10T20:46:58Z

Creation of the wikipage

New page

=== The Unicorn Tapeworm ===
== Hardware ==
[[File:Example.png|thumb|Wiring of PCB]]
The setup is compromised of :
* 1 Esp32
* 718 RGBW LED's
* 69 RGB LED's
* 1 Mosfet

The RGBW Strips are split in two:
* RGBW 1 is 430 pixels long
* RGBW 2 is 288 pixels long

The Mosfet is used to short the green PSU wire with ground, this enables you to power on or off the LED's whenever you want, the ESP32 is powered by a separate micro usb cable. The PSU is an old "server" powersupply and would ideally require replacement with a more fit for purpose one.
5V and Ground are connected to the LED strands with either some hacked together Molex connector or the Pcb. (Ground is also shared with the ESP32)

*RGBW 1 -> Pin 13
*RGBW 2 -> Pin 22
*RGB 1 -> Pin 23
*Mosfet -> Pin 15 + 3.3V

== Software ==
[[File:Example.png|thumb|WLED Setup]]
The ESP32 is running [https://kno.wled.ge/ WLED] , all you need to do is upload the latest version and configure the pins correctly.(see top)
Alternatively you can use this file to simply reconfigure everything.

The WLED installation should be preconfigured in HomeAssistant with adequate colors. The settings can also be configured by accessing the setup page locally under the Esp's ip.

@@ Line 2: / Line 2: @@
 |type=software
 |intro=A Led chain in Engineering
-|logo=https://5.imimg.com/data5/SELLER/Default/2022/2/PY/TL/KZ/13300543/rgb-led-strip-smd5050-ws2815-controls-250x250.jpg
+|logo=
 |status=running
 |repository=https://github.com/syn2cat/Unicorn_Tapeworm/tree/main

← Older revision		Revision as of 20:38, 10 December 2024
Line 1:		Line 1:
		+	{{Project
		+	\|type=software
		+	\|intro=A Led chain in Engineering
		+	\|logo=https://5.imimg.com/data5/SELLER/Default/2022/2/PY/TL/KZ/13300543/rgb-led-strip-smd5050-ws2815-controls-250x250.jpg
		+	\|status=running
		+	\|repository=https://github.com/syn2cat/Unicorn_Tapeworm/tree/main
		+	\|tracker=
		+	\|meetings=none
		+	\|contact=F3l1x
		+	\|members=Luna
		+	}}
		+
		+
		+
	=== The Unicorn Tapeworm ===		=== The Unicorn Tapeworm ===
	Multiple LED strips used to brighten up Engineering during winter months.		Multiple LED strips used to brighten up Engineering during winter months.

@@ Line 1: / Line 1: @@
 === The Unicorn Tapeworm ===
 Multiple LED strips used to brighten up Engineering during winter months.
+[https://github.com/syn2cat/Unicorn_Tapeworm/tree/main Github]
 == Hardware ==
 [[File:Example.png|thumb|Wiring of PCB]]
@@ Line 25: / Line 25: @@
 == Software ==
-[[File:Example.png|thumb|WLED Setup]]
+[[[[File:File:Example.png|thumb]]|WLED Setup]]
 The ESP32 is running [https://kno.wled.ge/ WLED] , all you need to do is upload the latest version and configure the pins correctly.(see top)
 Alternatively you can use this file to simply reconfigure everything.
 The WLED installation should be preconfigured in HomeAssistant with adequate colors. The settings can also be configured by accessing the setup page locally under the Esp's ip.

@@ Line 7: / Line 7: @@
 * 1 Esp32
 * 718 RGBW LED's
-* 69 RGB LED's
+* 96 RGB LED's
 * 1 Mosfet