Network hackerspace Strassen

From syn2cat - HackerSpace.lu
(Difference between revisions)
Jump to: navigation, search
Line 66: Line 66:
 
Note: PEAP+MSCHAPv2 will only work if you have changed your password on the syn<sub>2</sub>cat server after the 12th of October. Ask an admin for more information.
 
Note: PEAP+MSCHAPv2 will only work if you have changed your password on the syn<sub>2</sub>cat server after the 12th of October. Ask an admin for more information.
  
=== Basic wpa_supplicant configuration for H4x0roam ===
 
First install the H4x0roam SSL certificate chain:
 
<pre>
 
mkdir -p /etc/ssl/h4x0roam
 
wget http://www.hackerspace.lu/certs/syn2catCA.crt -O /etc/ssl/h4x0roam/syn2catCA.crt
 
wget http://www.hackerspace.lu/certs/syn2catInfr.crt -O /etc/ssl/h4x0roam/syn2catInfr.crt
 
wget http://www.hackerspace.lu/certs/lusitania.int.hackerspace.lu_infr.crt -O /etc/ssl/h4x0roam/lusitania.int.hackerspace.lu_infr.crt
 
cat /etc/ssl/h4x0roam/syn2catInfr.crt /etc/ssl/h4x0roam/syn2catCA.crt > /etc/ssl/h4x0roam/combined-ca.pem
 
chmod 0644 /etc/ssl/h4x0roam/*
 
</pre>
 
Please note that the 2 CA certificates have to be concatenated into a single file (this does only work with PEM certificated and not with DER certificates) to make wpa_supplicant accept tier 2 certifiactes (aka "certificates issued by a sub CA or intermediate CA").
 
 
Now add the following section to your '''/etc/wpa_supplicant.conf''' (you'll obviously have to fill in your own username and password):
 
<pre>
 
network={
 
ssid="h4x0roam"
 
bssid=00:21:29:E9:D1:AA
 
key_mgmt=WPA-EAP
 
eap=PEAP
 
identity="YOUR HACKERSPACE USERNAME"
 
password="YOUR HACKERSPACE PASSWORD"
 
phase2="auth=MSCHAPV2"
 
ca_cert="/etc/ssl/h4x0roam/combined-ca.pem"
 
client_cert="/etc/ssl/h4x0roam/lusitania.int.hackerspace.lu_infr.crt"
 
}
 
</pre>
 
Also make sure permissions are set correctly for wpa_supplicant:
 
<pre>chmod 0600 /etc/wpa_supplicant.conf</pre>
 
'''Warning:''' Please note that your syn<sub>2</sub>cat credentials are stored in '''cleartext''' on the hard disk unless you are using an encrypted hard disk. If you do not have an encrypted hard disk (for example due to a slow CPU), please use the [[Howto: H4x0roam with netcfg and encrypted wpa_supplicant config|advanced method with an encrypted wpa_supplicant configuration and a ramdisk]].
 
 
If wpa_supplicant throws error messages like
 
<pre>Failed to connect to wpa_supplicant - wpa_ctrl_open: No such file or directory</pre>
 
add the following line '''before''' the ''network={}'' section in your '''/etc/wpa_supplicant.conf''':
 
<pre>
 
ctrl_interface=/var/run/wpa_supplicant
 
</pre>
 
  
 
=== SSL certificates ===
 
=== SSL certificates ===
Line 155: Line 119:
 
After saving and activating the template, make sure to restart the wicd daemon and client. Next do a WiFi scan and configure an AP from the space, while using the newly created template !<br/>
 
After saving and activating the template, make sure to restart the wicd daemon and client. Next do a WiFi scan and configure an AP from the space, while using the newly created template !<br/>
 
You may specify a path to the CA certificate (see above)....you should do this actually, but still it's optional.
 
You may specify a path to the CA certificate (see above)....you should do this actually, but still it's optional.
 +
 +
==== Linux - wpasupplicant ====
 +
First install the H4x0roam SSL certificate chain:
 +
<pre>
 +
mkdir -p /etc/ssl/h4x0roam
 +
wget http://www.hackerspace.lu/certs/syn2catCA.crt -O /etc/ssl/h4x0roam/syn2catCA.crt
 +
wget http://www.hackerspace.lu/certs/syn2catInfr.crt -O /etc/ssl/h4x0roam/syn2catInfr.crt
 +
wget http://www.hackerspace.lu/certs/lusitania.int.hackerspace.lu_infr.crt -O /etc/ssl/h4x0roam/lusitania.int.hackerspace.lu_infr.crt
 +
cat /etc/ssl/h4x0roam/syn2catInfr.crt /etc/ssl/h4x0roam/syn2catCA.crt > /etc/ssl/h4x0roam/combined-ca.pem
 +
chmod 0644 /etc/ssl/h4x0roam/*
 +
</pre>
 +
Please note that the 2 CA certificates have to be concatenated into a single file (this does only work with PEM certificated and not with DER certificates) to make wpa_supplicant accept tier 2 certifiactes (aka "certificates issued by a sub CA or intermediate CA").
 +
 +
Now add the following section to your '''/etc/wpa_supplicant.conf''' (you'll obviously have to fill in your own username and password):
 +
<pre>
 +
network={
 +
ssid="h4x0roam"
 +
bssid=00:21:29:E9:D1:AA
 +
key_mgmt=WPA-EAP
 +
eap=PEAP
 +
identity="YOUR HACKERSPACE USERNAME"
 +
password="YOUR HACKERSPACE PASSWORD"
 +
phase2="auth=MSCHAPV2"
 +
ca_cert="/etc/ssl/h4x0roam/combined-ca.pem"
 +
client_cert="/etc/ssl/h4x0roam/lusitania.int.hackerspace.lu_infr.crt"
 +
}
 +
</pre>
 +
Also make sure permissions are set correctly for wpa_supplicant:
 +
<pre>chmod 0600 /etc/wpa_supplicant.conf</pre>
 +
'''Warning:''' Please note that your syn<sub>2</sub>cat credentials are stored in '''cleartext''' on the hard disk unless you are using an encrypted hard disk. If you do not have an encrypted hard disk (for example due to a slow CPU), please use the [[Howto: H4x0roam with netcfg and encrypted wpa_supplicant config|advanced method with an encrypted wpa_supplicant configuration and a ramdisk]].
 +
 +
If wpa_supplicant throws error messages like
 +
<pre>Failed to connect to wpa_supplicant - wpa_ctrl_open: No such file or directory</pre>
 +
add the following line '''before''' the ''network={}'' section in your '''/etc/wpa_supplicant.conf''':
 +
<pre>
 +
ctrl_interface=/var/run/wpa_supplicant
 +
</pre>
 +
  
 
==== Nokia/Symbian phones and foo ====
 
==== Nokia/Symbian phones and foo ====

Revision as of 21:31, 5 April 2011


Contents

Overview

Every hackerspace has a network to connect to the Internets, so does syn2cat

Bring your laptop or use one of the available PCs, plug it in and off you go. There's also wireless LAN available.


Layout

Here's the current layout in fancy ASCII art.

DSL -- thomson -- Lusitania :::: miniswitch == wall ports in ADHS rooms
                      ||
                      ||
                  3com Rack -- photoborg
                      "
                      "
                      "
                      "
                  3com Core == wall ports in syn2cat rooms
                      ||
                      ||
                  OpenDuino, switches, HPprinter, dd-wrt



Legend:

  * -- single cable
  * == more than one cable
  * "" fiber trunk
  * ::: VLAN
  * ... wlan cable

IP

We provide both IPv4 and IPv6 connectivity in the hackerspace.

Wireless

We have two access points (APs).
One of them operates in WPA2-Enterprise mode, the other in WPA2-Personal. The WPA2-Personal AP uses the formerly published pre-shared-password (you can find it in the space).

The WPA2-Enterprise AP uses a radius server for authenticating users with their WIKI account.
Only paying sy2cat members are able to use their WIKI login to access this AP.

Use the following settings:
Security: WPA2 Enterprise
Authentication: Tunneled TLS (TTLS)
Inner authentication: PAP
Username: <wiki-user>
Password: <wiki-password>

or

Security: WPA2 Enterprise
Authentication: PEAP
Inner authentication: MSCHAPv2
Username: <syn2cat-user>
Password: <syn2cat-password>


Be sure to use exactly those settings, else it will not work.
Note: PEAP+MSCHAPv2 will only work if you have changed your password on the syn2cat server after the 12th of October. Ask an admin for more information.


SSL certificates

There are a total of three certificates of interest.
We use a chained CA, making for a total of two CA certificates:
rootCA (PEM)
subCA (PEM)

And lastly for your convenience, a bundle of both in one file:
rootCA-subCA bundle (PEM)

For completeness, but you probably don't need it, the certificate of the internal server at the space:
lusitania-certificate (PEM)

OS compatibility

  • Linux works out of the box
  • Windows works out of the box
  • OSX works out of the box
  • iphone works out of the box
  • Android works out of the box
  • Symbian works fine (need to install CA certificates!, see earlier)
  • Maemo OS works out of the box

OS specific hints

Arch Linux

[Howto: H4x0roam with netcfg and encrypted wpa supplicant config]]

Linux - WICD template

Save this as "/etc/wicd/encryption/templates/peap-mschapv2" and add the filename to "/etc/wicd/encryption/templates/active".

name = PEAP with MSCHAPv2
author = syn<sub>2</sub>cat version = 1
require identity *Identity password *Password
optional ca_cert *Path_to_CA_Cert
-----
ctrl_interface=/var/run/wpa_supplicant
network={
ssid="$_ESSID"
scan_ssid=$_SCAN
proto=RSN
key_mgmt=WPA-EAP
pairwise=CCMP
eap=PEAP
phase1="peaplabel=0"
phase2="auth=MSCHAPV2"
identity="$_IDENTITY"
password="$_PASSWORD"
ca_cert="$_CA_CERT"
}

After saving and activating the template, make sure to restart the wicd daemon and client. Next do a WiFi scan and configure an AP from the space, while using the newly created template !
You may specify a path to the CA certificate (see above)....you should do this actually, but still it's optional.

Linux - wpasupplicant

First install the H4x0roam SSL certificate chain:

mkdir -p /etc/ssl/h4x0roam
wget http://www.hackerspace.lu/certs/syn2catCA.crt -O /etc/ssl/h4x0roam/syn2catCA.crt
wget http://www.hackerspace.lu/certs/syn2catInfr.crt -O /etc/ssl/h4x0roam/syn2catInfr.crt
wget http://www.hackerspace.lu/certs/lusitania.int.hackerspace.lu_infr.crt -O /etc/ssl/h4x0roam/lusitania.int.hackerspace.lu_infr.crt
cat /etc/ssl/h4x0roam/syn2catInfr.crt /etc/ssl/h4x0roam/syn2catCA.crt > /etc/ssl/h4x0roam/combined-ca.pem
chmod 0644 /etc/ssl/h4x0roam/*

Please note that the 2 CA certificates have to be concatenated into a single file (this does only work with PEM certificated and not with DER certificates) to make wpa_supplicant accept tier 2 certifiactes (aka "certificates issued by a sub CA or intermediate CA").

Now add the following section to your /etc/wpa_supplicant.conf (you'll obviously have to fill in your own username and password):

network={
	ssid="h4x0roam"
	bssid=00:21:29:E9:D1:AA
	key_mgmt=WPA-EAP
	eap=PEAP
	identity="YOUR HACKERSPACE USERNAME"
	password="YOUR HACKERSPACE PASSWORD"
	phase2="auth=MSCHAPV2"
	ca_cert="/etc/ssl/h4x0roam/combined-ca.pem"
	client_cert="/etc/ssl/h4x0roam/lusitania.int.hackerspace.lu_infr.crt"
}

Also make sure permissions are set correctly for wpa_supplicant:

chmod 0600 /etc/wpa_supplicant.conf

Warning: Please note that your syn2cat credentials are stored in cleartext on the hard disk unless you are using an encrypted hard disk. If you do not have an encrypted hard disk (for example due to a slow CPU), please use the advanced method with an encrypted wpa_supplicant configuration and a ramdisk.

If wpa_supplicant throws error messages like

Failed to connect to wpa_supplicant - wpa_ctrl_open: No such file or directory

add the following line before the network={} section in your /etc/wpa_supplicant.conf:

ctrl_interface=/var/run/wpa_supplicant


Nokia/Symbian phones and foo

Nokia/Symbian phones require you to install the CA certificates before they let you connect to a WPA-Enterprise network. They also mostly only support certificates in DER format.
So here go the CA certificate from above in DER format:
rootCA (DER)
subCA (DER)

Dev Links


Personal tools
Namespaces

Variants
Actions
Navigation
syn2cat
Hackerspace
Activities
Initiatives
Community
Tools
Tools